Thompson Fabricating, LLC
Request Quote
  • Home
  • Products
    • TUFRAIL Handrails
    • TUFLADDER
    • Ships Ladders
    • Gratings/Support Systems
    • Ladder Fall Arrest Systems
    • Dual Ladder Safety Posts
    • TUFGATE Stop Gates
    • Cover Plates
    • TUFHATCH Access Hatches
    • Portable Guardrail System
  • Engineering
  • Store
  • About Us
  • Contact Us
    • Rep Locator

Heavy Duty H20 Aluminum Access Hatch

<Back to TUFHATCH Access Hatches
interior access hatch - TH series
​
Features
  • 1/4 aluminum tread plate
  • Aluminum hold open device with red vinyl grip
  • 316 stainless steel gas springs
  • 316 stainless steel hardware
Options
  • ​Odortight
  • Gastight
  • Mebac slip resistant coating
  • Locking devices​

Downloads

H20 Specs (pdf)
File Size: 78 kb
File Type: pdf
Download File

Drawing

TH-series double leaf interior hatch drawing showing section through frame and side

Downloads

H20 TH Single Leaf Drawing (dwg)
File Size: 142 kb
File Type: dwg
Download File

H20 THG Single Leaf Drawing (dwg)
File Size: 156 kb
File Type: dwg
Download File

H20 TH Double Leaf Drawing (dwg)
File Size: 200 kb
File Type: dwg
Download File

H20 THG Double Leaf Drawing (dwg)
File Size: 200 kb
File Type: dwg
Download File

Specifications

Floor access doors shall be type "TH-H20" (gutterless) or "THG-H20" (gutter type) (WATERTIGHT, ODORTIGHT and GASTIGHT) as manufactured by Thompson Fabricating, LLC (Birmingham, AL). Door leaf shall be 1/4" aluminum checkered plate reinforced with structural aluminum channels and shall be capable of withstanding wheel loads up to AASHO-H20 at OFF-STREET locations only. (Calculations will be provided to the engineer upon request.) The following items shall be type 316 stainless steel: slam locks, brackets, hinges and hardware. The door shall have a 316 stainless steel gas spring with integral hold open device which will assist in opening the door and shall lock automatically in the open position. The door shall open a minimum of 90 degrees. The aluminum extruded frame shall have a thickness not less than 1/4" and shall incorporate a neoprene gasket that will reduce air leakage to less than 1 CFM per lineal foot of frame when the interior of the hatch is subjected to a 2 inch water column vacuum. For type "THG" doors the gutter frames shall be provided with a 1 1/2" threaded drain coupling. All fasteners which penetrate into the "Dry" area of the hatch shall be sealed with "O" Ring Seals to prevent incidental water and gas leakage. The portion of the frame which is in contact with the concrete shall receive a protective bituminous coating.

OPTIONS:
LOCKING DEVICES
SLIP RESISTANT COATINGS
​

NOTES: Independent Lab Test Reports are available upon request.
All double leaf access doors shall have two interconnected slam locks which latch at both ends of the plate and can be un-latched from a single point. "Watertight" for single leaf H20 doors shall be for a 1" to 2" head of water.
​

SIZES: Heavy Duty type "H20" Access doors are available in all "TH" and "THG" model sizes. 
Subscribe to Newsletter
  • Home
  • Products
    • TUFRAIL Handrails
    • TUFLADDER
    • Ships Ladders
    • Gratings/Support Systems
    • Ladder Fall Arrest Systems
    • Dual Ladder Safety Posts
    • TUFGATE Stop Gates
    • Cover Plates
    • TUFHATCH Access Hatches
    • Portable Guardrail System
  • Engineering
  • Store
  • About Us
  • Contact Us
    • Rep Locator